SmartThings Support

Honeywell Z-Wave Outlets, Switches, and Dimmers

Here's a bright idea: Using SmartThings with Honeywell Z-Wave Outlets, Switches, and Dimmers, you can control your lights at the tap of a button, create complex lighting automations, and monitor your smart home when you're not there.

 

This article will tell you how to connect the following Honeywell devices:

  • SmartThings app
  • SmartThings Classic app

To connect the Honeywell device in the SmartThings app

First, install the Honeywell device according to its installation instructions.

Next, in the SmartThings mobile app:

  1. From the Dashboard, tap Add device
  2. Android: Tap Add Device Manually
  3. For outlets:
    1. Select Outlet
    2. Tap Honeywell
  4. For switches:
    1. Select Switch/dimmer
    2. Tap Honeywell
  5. If you have more than one SmartThings Hub connected, select the Location you would like to add the device to, then tap Done
  6. While the Hub searches:
    • For outlets or plug-in modules, press the programming button once
    • For paddle switches, press the top rocker on the device
    • For toggle switches, press up on the toggle switch
  7. When the device is discovered, a message will appear that the device was successfully connected to your SmartThings Hub
  8. Tap Edit to rename the device
  9. When finished, tap Done
  10. Tap Done again to confirm

 

To reset the Honeywell device

If the Honeywell device was not discovered, you may need to reset, or “exclude,” the device before it can successfully connect with the SmartThings Hub. To do this, in the SmartThings mobile app:

  1. From the Dashboard, tap on the Devices tab
  2. Tap the Hub
  3. Tap the three dots in the top right
  4. Tap Z-Wave exclusion
  5. When prompted:
    • For outlets or plug-in modules, press the programming button once
    • For paddle switches, press the top rocker on the device
    • For toggle switches, press up on the toggle switch

After the app indicates that the device was successfully removed from SmartThings, follow the first set of instructions above to connect the Honeywell device.

 

To remove the Honeywell device from SmartThings

If the Honeywell device is connected but not operating as normal, you may need to remove the device and reconnect it with the SmartThings Hub.

To remove the device via the SmartThings app:

  1. From the Dashboard, tap on the Devices tab
  2. Tap the three dots in the top right
  3. Tap Edit
  4. Tap the red minus icon (-) next to the name of the device
  5. Confirm removal (this cannot be undone)
  6. When prompted, perform the exclusion procedure to remove the device from the mobile app and from the SmartThings Hub

 

To connect the Honeywell device in the SmartThings Classic app

First, install the Honeywell device according to its installation instructions.

Next, in the SmartThings Classic mobile app:

  1. Tap My Home
  2. Under Things, tap Add a Thing at the bottom of your Things list
  3. The app will say Looking for devices…
  4. While the Hub searches:
    • For outlets or plug-in modules, press the programming button once
    • For paddle switches, press the top rocker on the device
    • For toggle switches, press up on the toggle switch
  5. When the device is discovered, it will be listed at the top of the screen
  6. Tap the device to rename it and tap Done
  7. When finished, tap Save
  8. Tap Ok to confirm

 

To reset the Honeywell device

If the Honeywell device was not discovered, you may need to reset, or “exclude,” the device before it can successfully connect with the SmartThings Hub. To do this, in the SmartThings Classic mobile app:

  1. Tap the menu (Android) / More (iOS)
  2. Tap the Hub
  3. Tap Z-Wave Utilities
  4. Tap General Device Exclusion
  5. When prompted:
    • For outlets or plug-in modules, press the programming button once
    • For paddle switches, press the top rocker on the device
    • For toggle switches, press up on the toggle switch

After the app indicates that the device was successfully removed from SmartThings, follow the first set of instructions above to connect the Honeywell device.

 

To remove the Honeywell device from SmartThings Classic

If the Honeywell device is connected but not operating as normal, you may need to remove the device and reconnect it with the SmartThings Hub.

To remove the device via the SmartThings Classic app:

  1. Tap My Home
  2. Tap Things
  3. Select the device
  4. Tap the gear icon
  5. Tap Remove
  6. Confirm removal
  7. When prompted, perform the exclusion procedure to remove the device from the mobile app and from the SmartThings Hub

 

Attachments

File Size
39337-HQSG_v1.pdf 600 KB
39336-HQSG_v1.pdf 600 KB
39357_HQSG_v1.pdf 4 MB
39358-HQSG-v1-para.pdf 4 MB
39354_HQSG_v1.pdf 4 MB
39351_HQSG_v1.pdf 4 MB
39349_HQSG_v1.pdf 3 MB
39348-HQSG_v1.pdf 4 MB
39342-HQSG_v1.pdf 600 KB
39346-HQSG_v1.pdf 4 MB
39339-QSG-v1.pdf 600 KB